78 questions. Practise this paper at your own pace.
Choose another paper or set
Loading answer access…
Question 1
What is the dimensional formula of kinematic viscosity?
Question 2
Who appoints the chairman of Nepal Engineering Council?
Question 3
What is not an effective method to avoid corrosion?
Question 4
What does machine code M06 refer to?
Question 5
The work done in dropping an object from slanted height will be ______ compared to dropping in vertical height.
Question 6
What type of maintenance includes routine check up and inspection of equipment?
Question 7
Military organization is an example of:
Question 8
The term "cost down" refers to:
Question 9
Which of the following is true for phase change of saturated liquid to vapour?
Question 10
What does the term A/F, 7%, 8 does not refer to?
Question 11
Which type of working process is used for producing containers (like plastic jars)?
Question 12
Which type of working process produces better finish in materials?
Question 13
What is not a common type of welding defect?
Question 14
How does ionic crystal fracture?
Question 15
What is used to represent the quality of a grinding wheel?
Question 16
Which is not a liquid lubricant?
Question 17
How much area will a two-stroke engine occupy compared to a four-stroke engine for same power generation?
Question 18
For gears, how is comparison done between bending stress and contact stress?
Question 19
If N2 is greater than N1, what would be the action of a transformer?
Question 20
Oscillator is different from amplifier in:
Question 21
The first/detail drawing of the system is:
Question 22
The time between ordering and receiving of the order is:
Question 23
Ethics refers to:
Question 24
What does CAR represent?
Question 25
Relation between damping, stiffness and mass is:
Question 26
For liquid to slip in a container when it suddenly stops, the acceleration is proportional to:
Question 27
What is used to calibrate slip gauge?
Question 28
What is used to measure the inclination of a surface?
Question 29
Eddy current is used to measure:
Question 30
Who was the first to describe the term 'boundary layer'?
Question 31
Expansion process in Rankine cycle is:
Question 32
The diameter of the shank of the rivet depends upon?
Question 33
The longitudinal strain of the fibre depends upon:
Question 34
The boiling temperature of water is:
Question 35
One horse power is equal to:
Question 36
The heat treatment process for already hardened steel to soften it is:
Question 37
Conversion of fuel energy directly into mechanical energy is done by:
Question 38
Which of the following takes heat energy and converts it into mechanical work in a cycle?
Question 39
Degree of freedom for mechanism with 8 links and 9 revolute pairs is:
Question 40
Which of the risk is associated with software company?
Question 41
Heat flux is given by:
Question 42
Which of the following is not done by a fuel injector?
Question 43
The minimum operating pressure for free circulation boiler is:
Question 44
Top to down analysis in hazard analysis is:
Question 45
CNG is a:
Question 46
Which gear is used for intersecting shaft?
Question 47
Which type of cantilever beam provides more economic loading?
Question 48
How can we join two sheet metals?
Question 49
What is called the temperature where the ignition of substance starts?
Question 50
Fourier equation is:
Question 51
Determine the specific speed of the turbine with power 30000 kW, head of 35 m and rotating speed of 15 rpm.
Question 52
Determine the cutting speed of the grinder with diameter 15 mm and rpm of 150.
Question 53
Determine the maximum temperature in the diesel cycle with initial p=10 bar, T=295 K, compression ratio=4, cut-off ratio=2.
Question 54
A solid with 3.5 m width and 1 m depth is floating in water. Density = 850 kg/m³, length=5 m. Find centre of buoyancy from surface.
Question 55
The condition for self-locking in a brake is:
Question 56
Which type of projection is it when the projecting lines are parallel to each other & perpendicular to projecting plane?
Question 57
How does hypereutectoid steel form?
Question 58
Which type of projection is it when the projecting lines are parallel to each other & perpendicular to projecting plane?
Question 59
The ratio of maximum to mean velocity of laminar fluid passing through two parallel plates is:
Question 60
The process of extraction of (type of) iron is:
Question 61
Free convection depends on which of the following dimensionless numbers?
Question 62
Calculate the enthalpy of 1 kg of steam when, efficiency of boiler is 80%, feed water temperature is 50°C, and steam is dry saturated at 10 bar.
Question 63
Welding heat is inversely proportional to:
Question 64
Corrosion depends on:
Question 65
Which of the following exhaust content cannot be measured in emission tests?
Question 66
If a prismatic force P is applied on a solid cylinder of cross sectional area A, then which expression is correct?
Question 67
Expansion process in Rankine cycle is:
Question 68
Value of polytropic index for adiabatic process in an ideal gas is:
Question 69
Thermal stress on a material depends on:
Question 70
Which one of the following is not the standard attachment for milling operation?
Question 71
Calculate the present value of the future worth of Rs 500 at interest rate 8% PA and time 5 years.
Question 72
Which one gives return on investment to the investors?
Question 73
If viscous force is dominating inertia force in a fluid flow, the fluid flow is:
Question 74
The type of maintenance in which production is not halted is:
Question 75
The smell of exhaust in diesel engine is due to presence of:
Question 76
The manufacturing process for production of hollow samples/pipe is called:
Question 77
By considering following activities of a project, the project duration will be:
\[Table: A(4), B(5), C(3), D(7), E(5) days, predecessors: A:-, B:-, C:-, D:C, E:A,B,D]
Question 78
Under how many categories does the Nepal Engineering Council issue licenses?