Question 1Which condition is needed to turn off a latched conventional SCR by commutation?Report a question issueTell us what needs checking.Issue typeIncorrect answerMissing or unclear diagramFormatting problemQuestion or explanation unclearOtherDetails (optional)Review and send the email draft in Gmail. Nothing is sent automatically.Open Gmail draft Copy report detailsReports go to hello@licensepreparationnepal.com.A.Gate current increasesB.Gate is removed while anode current remains above holding currentC.Anode current rises above rated valueD.Anode current falls below holding current
Question 2A conducting MOSFET carries 5 A DC with 0.1 Ω on-resistance. What is conduction loss?Report a question issueTell us what needs checking.Issue typeIncorrect answerMissing or unclear diagramFormatting problemQuestion or explanation unclearOtherDetails (optional)Review and send the email draft in Gmail. Nothing is sent automatically.Open Gmail draft Copy report detailsReports go to hello@licensepreparationnepal.com.A.2.5 WB.0.5 WC.25 WD.5 W
Question 3How does an RC snubber across a semiconductor switch help?Report a question issueTell us what needs checking.Issue typeIncorrect answerMissing or unclear diagramFormatting problemQuestion or explanation unclearOtherDetails (optional)Review and send the email draft in Gmail. Nothing is sent automatically.Open Gmail draft Copy report detailsReports go to hello@licensepreparationnepal.com.A.Provides galvanic gate isolation by itselfB.Sets the transformer turns ratioC.Raises the output DC voltage referenceD.Limits the rate of voltage rise and damps transients
Question 4Which switch can conduct in both directions and is commonly used for AC phase control?Report a question issueTell us what needs checking.Issue typeIncorrect answerMissing or unclear diagramFormatting problemQuestion or explanation unclearOtherDetails (optional)Review and send the email draft in Gmail. Nothing is sent automatically.Open Gmail draft Copy report detailsReports go to hello@licensepreparationnepal.com.A.TRIACB.Single power diodeC.Unidirectional IGBT aloneD.Conventional SCR alone
Question 5What distinguishes a GTO from a conventional SCR?Report a question issueTell us what needs checking.Issue typeIncorrect answerMissing or unclear diagramFormatting problemQuestion or explanation unclearOtherDetails (optional)Review and send the email draft in Gmail. Nothing is sent automatically.Open Gmail draft Copy report detailsReports go to hello@licensepreparationnepal.com.A.It cannot be triggered at the gateB.Gate action can turn it offC.It conducts only at zero currentD.It has no anode terminal
Question 6What is diode reverse recovery?Report a question issueTell us what needs checking.Issue typeIncorrect answerMissing or unclear diagramFormatting problemQuestion or explanation unclearOtherDetails (optional)Review and send the email draft in Gmail. Nothing is sent automatically.Open Gmail draft Copy report detailsReports go to hello@licensepreparationnepal.com.A.A type of heatsinkB.Temporary reverse current while stored charge is removedC.Permanent reverse avalanche under any voltageD.Forward conduction at zero bias indefinitely
Question 7Why use a freewheel diode with a switched inductive load?Report a question issueTell us what needs checking.Issue typeIncorrect answerMissing or unclear diagramFormatting problemQuestion or explanation unclearOtherDetails (optional)Review and send the email draft in Gmail. Nothing is sent automatically.Open Gmail draft Copy report detailsReports go to hello@licensepreparationnepal.com.A.Raise normal supply frequencyB.Cause an instantaneous jump in inductor currentC.Provide a current path when the switch opensD.Force open-circuit voltage to rise without limit
Question 8Why is reducing switching frequency sometimes helpful thermally?Report a question issueTell us what needs checking.Issue typeIncorrect answerMissing or unclear diagramFormatting problemQuestion or explanation unclearOtherDetails (optional)Review and send the email draft in Gmail. Nothing is sent automatically.Open Gmail draft Copy report detailsReports go to hello@licensepreparationnepal.com.A.It reduces switching events and associated losses per secondB.It doubles conduction current automaticallyC.It eliminates all conduction lossesD.It increases transition energy in every switch
Question 9Why place a heat sink on a power semiconductor?Report a question issueTell us what needs checking.Issue typeIncorrect answerMissing or unclear diagramFormatting problemQuestion or explanation unclearOtherDetails (optional)Review and send the email draft in Gmail. Nothing is sent automatically.Open Gmail draft Copy report detailsReports go to hello@licensepreparationnepal.com.A.Provide a lower thermal-resistance path to ambientB.Raise its junction temperature at fixed dissipationC.Block gate currentD.Increase DC link voltage
Question 10Which device has an insulated MOS gate and bipolar conduction behavior?Report a question issueTell us what needs checking.Issue typeIncorrect answerMissing or unclear diagramFormatting problemQuestion or explanation unclearOtherDetails (optional)Review and send the email draft in Gmail. Nothing is sent automatically.Open Gmail draft Copy report detailsReports go to hello@licensepreparationnepal.com.A.IGBTB.TRIACC.Conventional SCRD.Power diode